Return to supplier page
3M™ Dyneon™ PTFE Micropowder TF 9205 by 3M acts as anti-stick agents. It is a micro powder that lowers coefficient of friction when blended into other polymers or liquids. In addition, it can be effective as a rheological modifier (thickening agent)and significantly increases viscosity when added to liquids and this feature is less temperature-dependent than many other modifiers. It exhibits chemical and thermal stability. It is highly hydrophobic filler and can be used to improve abrasion resistance. Because of its small particle size coupled with good free-flowing properties, it exhibits very good metering behavior and can be easily incorporated into other materials (even in dry blends). It can be added to lubricant oils/greases and waxes, polymers, paints, elastomers and coatings. It is recommended for use in printing inks and antifriction coatings in the non-food sector. Typical additional quantity varies between 1-20% depending on the selected matrix and the desired properties. 3M™ Dyneon™ PTFE Micropowder TF 9205 approved by the German Federal Institute for Consumer Health Protection and Veterinary Medicine (BgVV). 3M™ Dyneon™ Fluoroplastic E-15188H THV by 3M is a fluorothermoplastic containing tetrafluoroethylene, hexafluoropropylene and vinylidene fluoride. Exhibits excellent flexibility, excellent chemical resistance, excellent permeation resistance to fuels, high transparency and low refractive index. Provides a balance of low temperature processing, low flammability, thermal stability, and melt process ability. Possesses excellent weather ability and good anti-soiling properties. Bondable to itself and other substrates (for multi-layer constructions). 3M™ Dyneon™ Fluoroplastic E-15188H THV by 3M is applicable in wire coatings. 3M™ Dyneon™ Fluoroplastic THV 500GX4Z by 3M is a fluorothermoplastic containing tetrafluoroethylene, hexafluoropropylene and vinylidene fluoride. Exhibits high flexibility, excellent chemical resistance, high transparency and low refractive index. Provides a balance of solvent processing, low flammability, thermal stability and melt process ability. Possesses excellent weather ability and good anti-soiling properties. Bondable to itself and other substrates (for multi-layer constructions). 3M™ Dyneon™ Fluoroplastic THV 500GX4Z by 3M is applicable in wire coatings. 3M™ Dyneon™ Fluoroplastic THV 221GZ by 3M is fluorothermoplastic containing tetrafluoroethylene, hexafluoropropylene and vinylidene fluoride. Exhibits excellent flexibility, e-beam crosslinking property and low refractive index. Provides a balance of solvent processing, low flammability, thermal stability and high transparency. Possesses excellent weather ability and good anti-soiling properties. Bondable to itself and other substrates (for multi-layer constructions). 3M™ Dyneon™ Fluoroplastic THV 221GZ by 3M is applicable in wire coatings. 3M™ Dyneon™ Fluoroplastic THV 500GZ by 3M is a fluorothermoplastic containing tetrafluoroethylene, hexafluoropropylene and vinylidene fluoride. Exhibits high flexibility, excellent chemical resistance, high transparency and low refractive index. Provides a balance of solvent processing, low flammability, thermal stability and melt process ability. Possess excellent UV stability, excellent weather ability and good anti-soiling properties. Bondable to itself and other substrates (for multi-layer constructions). 3M™ Dyneon™ Fluoroplastic THV 500GZ by 3M is applicable in wire coatings. 3M™ Dyneon™ Fluoroplastic THV 415GZ by 3M is a fluorothermoplastic containing tetrafluoroethylene, hexafluoropropylene and vinylidene fluoride. Exhibits high flexibility, excellent chemical resistance, high transparency and low refractive index. Provides a balance of solvent processing, low flammability, thermal stability and melt processability. Possesses excellent weatherability and good anti-soiling properties. Bondable to itself and other substrates (for multi-layer constructions). 3M™ Dyneon™ Fluoroplastic THV 415GZ by 3M is applicable in wire coatings. 3M™ Dyneon™ Fluoroplastic THV 221AZ by 3M is a fluorothermoplastic containing tetrafluoroethylene, hexafluoropropylene and vinylidene fluoride. Exhibits excellent flexibility, e-beam crosslinking property and low refractive index. Provides a balance of solvent processing, low flammability, thermal stability and high transparency. Possesses excellent weather ability and good anti-soiling properties. Bondable to itself and other substrates (for multi-layer constructions). 3M™ Dyneon™ Fluoroplastic THV 221AZ by 3M is applicable in architectural, wire and cast coatings. 3M™ Dyneon™ PTFE Dispersion TF 5070GZ by 3M is water-based fluoropolymer dispersion. Exhibits excellent chemical resistance, abrasion resistance and very good anti-stick properties. Has a large operating temperature range and improved film formation and low settling tendency. Provides corrosion resistance and better adhesion and gloss. Suitable for manufacturing bimodal systems. Recommended for coating metals and ceramic surfaces in industrial bake ware, e.g. baking pans or baking trays. and in non-stick household applications, e.g. frying pans, pots, rice cookers. Listed in FDA. 3M™ Dyneon™ PTFE Dispersion TF 5070GZ by 3M is approved by the German Federal Ministry of Health (BGA). 3M™ Dyneon™ Fluoroplastic FEP 6300GZ by 3M Dyneon is a water-based fluorothermoplastic polymer dispersion. Exhibits a large operating temperature range, very good non-stick properties, universal chemical resistance, high shear stability and low settling tendency. Shows a high degree of transparency of the polymer film. Improves substrate adhesion and can increase the corrosion protection and gloss of the coating. Can be mixed with fillers or pigments for use in coating formulations. Recommended for formulating systems of coating metal and ceramic surfaces in industrial bake ware, e.g. baking pans or baking trays and non-stick household applications, e.g. frying pans, pots, rice cookers. Various techniques such as spray coating, roller coating and silk-screen coating can be employed. Listed in U.S. FDA, approved by the German Federal Ministry of Health (BGA) and 3M™ Dyneon™ Fluoroplastic FEP 6300GZ by 3M Dyneon is recommended by the German Federal Institute for Risk Assessment (BfR). 3M™ Dyneon™ PTFE Dispersion TF 5035GZ by 3M is water-based fluoropolymer dispersion. Exhibits good chemical resistance, good stability, good film formation and low settling tendency. Has a large operating temperature range and very good non-stick properties. Recommended for use in aqueous non-stick coatings systems for metals, glass, ceramic surfaces, and cookware, e.g. frying pans. Suitable for sintered coatings with food contact (EU, FDA). Various techniques such as spray coating, roller coating and silk-screen coating can be employed. 3M™ Dyneon™ PTFE Dispersion TF 5035GZ by 3M is listed in U.S. FDA.
3M™ Dyneon™
Coating ingredients supplied by 3M