Polyphthalamide (PPA)

ForTii® Ace MX51 by Envalior is a heat stabilized, 30% glass-reinforced, PPA (PA4T) for automotive applications. It is a PPA with unique fatigue performance and chemical resistance. The high aromatic content and high Tg lead to excellent part stiffness and low creep, even up to 150°C. The moisture uptake occurs slowly with a very limited impact on dimensions. ForTii® Ace MX51 is suitable for processing by injection molding. It is used in structural parts with ForTii® Ace.

ForTii® F11 by Envalior is a halogen- and red phosphorous-free, chemical resistant, 30% glass-reinforced PPA, polyamide 4T (PA4T) grade. It is suitable for processing by injection molding. It offers an excellent balance in flow, toughness and stiffness, enabling thin walls or complicated geometries for E&E applications. ForTii® F11 is all-color VDE approved, has a high RTI electrical rating of 140°C at 0.75 mm and CTI =800V rating to secure thermal aging and electrical performance. It is used in automotive e-motor bobbins, brush holders (electro motors), coil insulation, contactors, EGR sensor, laminates (electro motors), battery-, FPC-, HDMI-, WtB and BtB-, reflow connectors, reflow connectors (2), reflow connectors (3) as well as speed-, temperature-, position sensor, MCCB housings, fuse holder, high voltage connector e-motor, industrial control gear, medium voltage circuit breaker isolators, medium voltage circuit breaker, micro appliance connector, miniature circuit breakers, molded case circuit breakers, motor starter/overload relays, start/stop: alternator and starter parts.

ForTii® Ace XTR31S by Envalior is an unreinforced, lubricated, medium/high viscosity, PPA (PA4T). This high-temperature polyamide has excellent viscosity stability, chemical resistance, barrier performance and stable processing. It is used in many coextrusion and pultrusion processes.

ForTii® XS51 by Envalior is a flame retarded, 50% glass fiber reinforced, PPA (PA 4T) grade. It is halogen & red phosphorous-free. It is suitable for processing by injection molding. It provides good chemical resistance, and excellent balance of mechanical strength and flow. It offers stable process behavior that allows high-quality surface requirements such as notebook covers. It supports complicated geometry design and enabling robust mechanical performance in the drop test. ForTii® XS51 is used in medium voltage circuit breakers embedded pole, notebook housing and medium voltage circuit breakers.

ForTii® K11 by Envalior is a 30% glass reinforced, good flow, electro-friendly, PPA (PA4T) grade. It offers goood chemical resistance and combined excellent mechanical properties with low warpage for miniature applications such as audio jack and camera holder. It is suitable for processing by injection molding. ForTii® K11 is designed for position-, speed and temperature sensors.

ForTii® Ace MX53 by Envalior is a 30% glass-reinforced, heat-stabilized, PPA (PA4T) for automotive applications. It is suitable for processing by injection molding. It is a PPA offering fatigue performance and chemical resistance. It possesses high aromatic content and high Tg leads to excellent part stiffness and low creep. ForTii® Ace MX53 moisture uptake occurs slowly with a very limited impact on dimensions. It is designed for carburetor adapter heat shield insulation wall and structural parts with ForTii® Ace.

ForTii® LDS51B by Envalior is a halogen- & red phosphorus-free, truly reflow compatible and flame retarded, PPA (PA 4T) grade. It is reinforced with 30% glass fiber. It is suitable for processing by injection molding. It exhibits good chemical resistance, superior plating performance and is compatible with a broad range of laser settings enabling high resolution and fine-line capability. ForTii® LDS51B is applicable for laser direct structuring.

ForTii® JTX2 by Envalior is an electro-friendly, PPA (PA4T) grade reinforced with 30% glass fiber. It is suitable for processing by injection molding and shows consistent performance. It offers good chemical resistance, robust mechanical performance and has good reliability in thermal aging and mechanical shocks. It possesses low risk of blistering due to its JEDEC MLS 1 rating for specified thicknesses. It is recommended for HB reflow headers/connectors in (automotive) electronics. ForTii® JTX2 is used in automotive reflow connectors and car computer control system.

ForTii® F12 by Envalior is a halogen- and red phosphorous-free, electro-friendly, PPA (PA4T) grade. It is reinforced with 40% glass fiber. It offers good chemical resistance, an excellent balance of stiffness and toughness. It is suitable for high mechanical loaded applications such as power connectors or EV parts. It is processed by injection molding. It has high RTI electrical rating of 140°C at 0.75mm. It shows JEDEC Level 2 performance, enabling SMT process without deformation and low risk on blistering. ForTii® F12 is used in industrial control gear, MCCB housings, medium voltage circuit breakers and medium voltage circuit breakers embedded pole.

ForTii® Eco E11 by Envalior is a halogen- and red phosphorous-free, chemical resistant, 30% glass reinforced, PPA (PA4T) grade. It offers an excellent balance in flow, toughness and stiffness with superior processing performance. It exhibits improved toughness, high electrical RTI rating of 150°C at 0.75 mm and has CTI 600V. It is eco-friendly in nature due to its partly bio-based content. ForTii® Eco E11 is suitable for processing by SMT and injection molding. It is a certified V-0 at 0.15mm. It is used in audio jack-, DDR DIMM- and reflow connectors.